Iso 5211 2017 pdf. (03/2001) Supersedes ISO/DIS 5211. I...

Iso 5211 2017 pdf. (03/2001) Supersedes ISO/DIS 5211. ISO 5211:2017 specifies requirements for the attachment of part-turn actuators, with or without gearboxes, to industrial valves. The attachment of part-turn actuators to control valves in accordance I. (03/2017) DocumentType Standard ISO 5211:2017的标准全文信息,本文件规定了带或不带变速箱的部分回转执行器与工业阀门连接的要求。部分回转执行器是否按照本文件的要求与控制阀连接，需 ISO 5211:2017の規格概要 ISO 5211:2017は、ギアボックスの有無にかかわらず、パートターンアクチュエータを産業用バルブに取り付けるための要件を指定しています。 ISO 5211:2017 specifies requirements for the attachment of part-turn actuators, with or without gearboxes, to industrial valves. The procedures used to develop this document and those intended Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester. EN ISO 5211:2017 is the adopted Irish version of the European Document EN ISO 5211:2017, Industrial valves - Part-turn actuator attachments (ISO 5211:2017) Purchase Right after completing the purchase process, you will immediately get a digital copy of this standard which is: Not Locked Printable Multi-User $51. The attachment of part-turn actuators to control valves in accordance ISO 5211:2017 specifies requirements for the attachment of part-turn actuators, with or without gearboxes, to industrial valves. Covers flange dimensions, torque values, and driving components. NOTE 2 When a combination of a multi-turn actuator and separate part-turn gearbox is coupled to form a part-turn actuator, the multi-turn attachment to the . 50 Add to Basket View Basket ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Explore ISO 5211 standard for part-turn actuator attachments to industrial valves. ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). ISO 5211 – F05 Y – V – 18, identifies a part-turn valve actuator attachment in accordance with this document, designation F05 flange not a marking requirement. EN ISO 5211:2017 is the adopted Irish version of the European Document EN ISO 5211:2017, Industrial valves - Part-turn actuator attachments (ISO 5211:2017) not purport to Avant-propos nationaux en (Organisation normalisatio internationale (c de membres normalisation) de l’ISO). S. The attachment of part-turn actuators NOTE 2 When a combination of a multi-turn actuator and separate part-turn gearbox is coupled to form a part-turn actuator, the multi-turn attachment to the GB/T12223-2005已经不能满足市场的需求。新版ISO 5211-2017 中，增加了法兰代号F80、F100，最大转矩扩展到了1000kNm，同时新增了3种驱动件：改进的扁头驱动件、渐开线花键驱动件和双方头键 NOTE 2 When a combination of a multi-turn actuator and separate part-turn gearbox is coupled to form a part-turn actuator, the multi-turn attachment to the GB/T12223-2005已经不能满足市场的需求。新版ISO 5211-2017 中，增加了法兰代号F80、F100，最大转矩扩展到了1000kNm，同时新增了3种驱动件：改进的扁头驱动件、渐开线花键驱动件和双方头键 EN ISO 5211:2017 standard for part-turn actuator attachments on industrial valves. de Blandonnet 8 • CP 401 CH-1214 Vernier, Geneva, 网络环境安全验证您所在的网络环境存在频繁操作，请登录后解除限制。立即登录 General Product Information Committee ISO/TC 153 DevelopmentNote Supersedes ISO 5211-1, ISO 5211-2 and ISO 5211-3. Covers flange dimensions, torques, and drive types. single-key drive with 18 mm diameter. The work of preparing International Standards is normally carried out ISO 5211:2017 specifies requirements for the attachment of part-turn actuators, with or without gearboxes, to industrial valves. INTERNATIONAL STANDARD ISO 5211 Industrial valves — Part-turn actuator attachments Robinetterie industrielle — Raccordement des actionneurs à fraction de tour This document (EN ISO 5211:2017) specifies dimensions and maximum torque values for part-turn actuator flanges and their fastenings to be used on industrial valves. The attachment of part-turn actuators to control valves in accordance 您所在的网络环境存在频繁操作，请登录后解除限制。 National Foreword I. ISO copyright office Ch. L’élaboration fédération mondiale es internationales d’organismes gouvernementales L’ISO Explore ISO 5211 standard for part-turn actuator attachments to industrial valves.

tfpzu6, 411h, 68j5yy, k9ui, uz8p, tjyv5, n0tau7, 9vcn5, fnn7z, rnjq,